气体增压泵在使用一段时间后会出现增压泵不工作或者上压慢等故障,现在小编就将气体增压泵常见的几种故障通过表现来分析出现这种情况的原因和解决方法告诉大家。
After using the gas booster pump for a period of time, there will be failures such as the booster pump does not work or the pressure is slow. Now Xiaobian will analyze the causes and solutions of this situation through the performance of several common failures of the gas booster pump.
1.故障表现：当驱动气体压力不低于20psi时，驱动部分不工作或不循环。
1. Fault performance: when the driving gas pressure is not lower than 20psi, the driving part does not work or circulate.
可能原因：供气管路堵塞或供气量不足；空气循环阀堵塞；排放口结冰；消声器堵塞。
Possible causes: the air supply pipeline is blocked or the air supply is insufficient; The air circulation valve is blocked; The discharge port is frozen; The muffler is blocked.
解决方法;检查气体供应管道和空气调压阀；拆卸空气循环阀，并使用允许溶剂进行清洗；驱动气体水含量较高，改用更好的干燥设备；将消声器拆卸下来清洗。
resolvent; Check the gas supply pipeline and air pressure regulating valve; Disassemble the air circulation valve and clean it with allowable solvent; The water content of the driving gas is high, so better drying equipment should be used; Remove the muffler for cleaning.
2.故障表现：在负载情况下，驱动部分不工作，并在换向排气口有连续气体排出。
2. Fault performance: under load, the driving part does not work, and there is continuous gas discharge at the reversing exhaust port.
可能原因：换向针的弹簧破坏或不适合；换向针末端O型圈不适合或失去作用。
Possible causes: the spring of the reversing needle is damaged or unsuitable; The O-ring at the end of the reversing needle is not suitable or loses its function.
解决方法;置换弹簧；置换O型圈。
resolvent; Replace the spring; Replace the O-ring.
3.故障表现：驱动部分不工作；消声器泄露空气。
3. Fault performance: the driving part does not work; The muffler leaks air.
可能原因：驱动气体流量不足；空气循环阀芯的密封收缩或损坏。
Possible causes: insufficient flow of driving gas; The seal of the air circulation valve core shrinks or is damaged.
解决方法;提高驱动气体流量；检测空气循环阀芯的密封，如果损坏，更换并组装重新测试；如果没有损坏，检查驱动部分密封。
resolvent; Increase the flow of driving gas; First, check the seal of the air circulation valve core. If it is damaged, replace it, assemble it and retest it; If there is no damage, check the drive part seal.
4.故障表现：驱动部分工作，但气体没有增压。
4. Fault performance: the driving part works, but the gas is not pressurized.
可能原因：气体压缩部分的单向阀密封或高压部分损坏。
Possible causes: the one-way valve seal of the gas compression part or the high-pressure part is damaged.
解决方法;检查单向阀及高压端。
resolvent; Check the check valve and high pressure end.
This is the reason for the failure of the booster pump. I hope I can help you. Please come to our website for more relevant information http://www.feileisi.com Consult!
