气体增压泵的作用就是输入其中，增压阀就可以输出倍数高压气体,可以达到2倍或者5倍的高压气体。并增压阀无需电源驱动，安装和移动都很方便。输出的压力和驱动都可以手动调节,操作简单，实用性很强。下面来讲讲气体增压泵的正确选型以及其他方面要求吧。
The function of the gas booster pump is to input it, and the booster valve can output multiple high-pressure gas, which can reach 2 or 5 times of high-pressure gas. The booster valve does not need to be driven by power supply, so it is convenient to install and move. The output pressure and drive can be adjusted manually, which is simple to operate and highly practical. Let's talk about the correct selection of gas booster pump and other requirements.
正确选型
Correct model selection
增压阀可以对、氮气、氧气、氢气等气体增压，如果为腐蚀性气体，如H2S,SO2等e气体,在选型时客户应主动说明所需压力及流量大小。
The booster valve can pressurize, nitrogen, oxygen, hydrogen and other gases. If it is corrosive gas, such as H2S, SO2 and other e gases, the customer should actively explain the required pressure and flow during model selection.
过滤要求
Filtration requirements
增压阀动力源为压缩,要求气源洁净，颗粒要求在5um以下,一般工厂气源比较脏如果不经过滤直接接到阀上,长期使用，泵会长期积污,会导致单向阀失灵、密封圈磨损严重.
The power source of the booster valve is compression. The air source is required to be clean, and the particles are required to be less than 5um. Generally, the air source of the factory is dirty. If it is directly connected to the valve without filtration, the pump will accumulate dirt for a long time, which will lead to the failure of the check valve and serious wear of the sealing ring
安装要求
Installation requirements
安装时驱动气源要使用PU风管,原因容易安装操作方便管内不会生锈，如果使用金属管，安装前要用压缩吹扫，避免焊渣吹到换向阀内,将换向阀卡死。驱动气源的纯净度和介质可以影响到其使用寿命，普通压缩没有经过冷干机或者过滤器的会有一定的水分和杂质，这些水分和杂质进入到增压泵内部会形成阻力影响其工作效率，长时间使用会刮伤其密封圈和缸筒。
During installation, the driving air source should use Pu air duct, which is easy to install and operate, and the pipe will not rust. If metal pipe is used, it should be compressed and purged before installation to avoid welding slag blowing into the change-over valve and blocking the change-over valve. The purity and medium of the driving air source can affect its service life. There will be certain moisture and impurities in the ordinary compressed air that has not passed through the cold dryer or filter. These moisture and impurities will form resistance when entering the booster pump, affecting its working efficiency, and will scratch its sealing ring and cylinder barrel after long-term use.
Safe operation process of gas booster pump equipment:
1、操作者需要熟悉设备的一般结构及性能,严禁超性能使用设备。
1. The operator needs to be familiar with the general structure and performance of the equipment, and it is strictly forbidden to use the equipment beyond its performance.
2、操作者前检查气管,接头,过滤器，否漏气。
2. Before the operator, check the air pipe, connector and filter for air leakage.
3、拚气阀，调整气压调节阀把输出气压调整到需用的数值，(罐压≤0.95Mpa)
3. Air valve, adjust the air pressure regulating valve to adjust the output air pressure to the required value, (tank pressure ≤ 0.95mpa)
4、观察增压泵是否能正常工作。
4. Observe whether the booster pump can work normally.
5、观察储气罐压力表是否达到设定值、达到设定值时,增压泵是否停止工作。
5. Observe whether the pressure gauge of the air reservoir reaches the set value and whether the booster pump stops working when it reaches the set value.
6、待增压泵停止工作后，再次检查调节阀压力设定与罐表压是否相符。
6. After the booster pump stops working, check again whether the pressure setting of the regulating valve is consistent with the tank gauge pressure.
7、工作完毕后要关闭气阀,清洁机器。
7. Close the air valve and clean the machine after work.
The above is all about the problems and precautions introduced to you today. I hope it can help you. If you want to know more, you can contact us by phones or follow our website http://www.feileisi.com , our staff will contact you in time.
