空气增压泵，是专为针对解决一般场合下压缩空气的压力过低而专门设计的产品，具有结构可靠、寿命长、稳定性高、无需要用电、维护简单等特点。该系列产品能够使压缩空气通过自增压的方式输出较高的压力。泵体全部采用铝合金及不锈钢制造，全部密封件均为进口产品，可长时间连续工作，驱动气压均不可以大于8.3Bar系列空气增压泵的驱动压力连接范围在（1Bar-8.3Bar max）。
The air booster pump is specially designed to solve the low pressure of compressed air in general occasions. It has the characteristics of reliable structure, long service life, high stability, no need of electricity, simple maintenance and so on. This series of products can make the compressed air output higher pressure through self pressurization. The pump body is made of aluminum alloy and stainless steel. All seals are imported products, which can work continuously for a long time. The driving pressure can not be greater than 8.3bar. The driving pressure connection range of 8.3bar series air booster pump is (1bar-8.3bar max).
操作要求：
Operation requirements:
1、工作环境要求无尘，无腐蚀。
1. The working environment shall be free of dust and corrosion.
2、每台增压泵都配置有两个L脚架，说明部分备注有安装、空间需要尺寸。
2. Each booster pump is equipped with two l-stands, indicating that some remarks have the required dimensions of installation space.
空气增压泵尺寸
Size of air booster pump
气源要求：
Air source requirements:
气体接入
Gas access
在标注有驱动接口（端口螺纹安装尺寸有备注），接入驱动和预压缩介质，建议配置过滤器装置精度满足我们要求，驱动进气配置油雾器对泵体本身起到润滑作用（油雾器建议添加VG32的透平油，其它油会加快密封件的老化）。
When the drive interface is marked (there are remarks on the installation size of the port thread), the drive and pre compression media are connected. It is recommended to configure the filter device, and the accuracy meets our requirements. The drive inlet is equipped with an oil mist to lubricate the pump body itself (it is recommended to add vg32 turbine oil to the oil mist, and other oil will accelerate the aging of the seal).
管路要求
Pipeline requirements
根据泵的输出压力，必须选择能承受泵输出压力的管路。
According to the output pressure of the pump, the pipeline that can bear the output pressure of the pump must be selected.
启动
start-up
1.确保所有的接口都紧固连接而且原件安装到位。
1. Ensure that all interfaces are firmly connected and the original parts are installed in place.
2.调节减压阀，将气压调到O psi。
2. Adjust the pressure reducing valve and adjust the air pressure to o psi.
3.打开进气开关，慢慢调大减压阀直到泵启动（正常情况下泵的启动压力在15～20psi）,继续调4.节观察高压压力表，达到您需要的压力。
3. Turn on the air inlet switch, slowly increase the pressure reducing valve until the pump starts (normally, the starting pressure of the pump is 15 ~ 20psi), and continue to adjust 4 Observe the high pressure gauge in this section to reach the pressure you need.
Gas liquid booster pump focuses on providing customers with satisfactory service. For more wonderful contents, please click to enter our website http://www.feileisi.com , we will have more wonderful content for you to check
